Increase the Quality of Life through the Development of Automation

Anoushe Arab (Education office of Zahedan, Iran)

Article ID: 1367


This paper discusses needs for the automation of the underdevelopment communities. The novelty of this research is the link between production of microprocessors and increasing of the life quality. This study highlights the importance of efficient and economic architecture of logical circuits for the automation.  The aim of this research is to produce a logical circuit, which includes suitable gates. The circuit will be embedded in the automatic devices as a microprocessor to cause programmed functions. This research reports analytically a workshop method to build the circuit. It uses an assembly card and required gates.  Then, it suggests certain VHDL codes to drive a motor.  The workshop presents the configuration schemes and connection board for every gate. In addition, it shows a schematic wiring diagram of the circuit. Finally, the economic analysis proves the mass production of the circuit will enhance the automation and consequently the quality of life. The outcome of this research is a helpful experience to the engineers, manufacturers and students of the relevant disciplines to resolve the inequality in the use of the modern technologies.  


Logic circuits、Digital gates、Microprocessors、Mass production、Quality of life、Assembly card

Full Text:



[1] Allan, A., Edenfeld, D., Joyner, W. H., Kahng, A. B.,Rodgers, M., & Zorian, Y.. 2001 technology roadmap for semiconductors. Computer, 2002, 35(1): 42-53.

[2] Antonakos, J. L.. The 68000 Microprocessor: Hardware and Software Principles and Applications. Prentice Hall PTR, 1998.‏

[3] Auch, A. G., & Joosep, H.. Automatic engineering change analysis for incremental timing analysis. IBM technical disclosure bulletin, 1984, 26(10): 5127-5131.

[4] Austin, T. M.. DIVA: A reliable substrate for deep submicron microarchitecture design in MICRO-32.Proceedings of the 32nd Annual ACM/IEEE International Symposium on Microarchitecture. IEEE, 1999:196-207.

[5] Baker, R. J.. CMOS: circuit design, layout, and simulation. Wiley-IEEE press, 2019.

[6] Battini, D., Faccio, M., Ferrari, E., Persona, A., & Sgarbossa, F.. Design configuration for a mixed-model assembly system in case of low product demand.The International Journal of Advanced Manufacturing Technology, 2007, 34(1-2): 188-200.

[7] Bischof, C. H., Roh, L., & Mauer‐Oats, A. J..ADIC: an extensible automatic differentiation tool for ANSI‐C. Software: Practice and Experience,1997, 27(12): 1427-1456.

[8] Boothroyd, G.. Assembly automation and product

[9] design. CRC Press, 2005.

[10] Card, S. K.. The psychology of human-computer interaction. CRC Press, 2018.

[11] Ebrahimzadeh, I., Shahraki, A. A., Shahnaz, A. A., & Myandoab, A. M.. Progressing urban development

[12] and life quality simultaneously. City, Culture and Society, 2016, 7(3): 186-193.

[13] Giordano, G.. Buying Power: As Industry 4.0 continues to influence the plastics industry, manufacturers must consider connectivity and other factors when purchasing equipment. Plastics Engineering, 2019,75(1): 28-35.

[14] Hemert, L. H.. Digitala kretsar. Studentlitteratur,

[15] ‏.2001

[16] Hnatek, E. R.. Integrated circuit quality and reliability. CRC Press, 1994.

[17] Koç, T. Ç.. The importance of high technology for economic development: a comparative analysis of Turkey and South Korea (Master’s thesis, Işık Üniversitesi), 2019.

[18] Libes, D.. Exploring Expect: a Tcl-based toolkit for

[19] automating interactive programs. O’Reilly Media,

[20] Inc., 1995.

[21] Maheshwary, S.. Automated Feature Construction and Selection (Doctoral dissertation, International Institute of Information Technology Hyderabad), 2019.

[22] Nichols, J., Myers, B. A., & Litwack, K.. Improving automatic interface generation with smart templates.In Proceedings of the 9th international conference on Intelligent user interfaces. ACM, 2004: 286-288.

[23] Patterson, D. A., & Sequin, C. H.. Design considerations for single-chip computers of the future. IEEE Journal of Solid-State Circuits, 1980, 15(1): 44-52.

[24] Paul, B. K., Panat, R., Mastrangelo, C., Kim, D., & Johnson, D.. Manufacturing of smart goods: Current state, future potential, and research recommendations. Journal of Micro and Nano-Manufacturing,2016, 4(4): 044001.

[25] Peatman, J. B.. Microcomputer-based design. McGraw-Hill, Inc., 1977.

[26] Shahraki, A. A.. Regional development assessment:Reflections of the problem-oriented urban planning.Sustainable cities and society, 2017, 35: 224-231.

[27] Shahraki, A. A.. Supplying water in hydro-drought regions with case studies in Zahedan. Sustainable Water Resources Management, 2019, 5(2): 655-665.

[28] Siddiquee, N. A.. E-government and transformation of service delivery in developing countries: The Bangladesh experience and lessons. Transforming Government: People, Process and Policy, 2016, 10(3):368-390.

[29] Sugihara, T., Yamamoto, K., & Nakamura, Y.. Hardware design of high performance miniature anthropomorphic robots. Robotics and Autonomous Systems,2008, 56(1): 82-94.

[30] Tersine, R. J.. Production/Operations Management:

[31] Concepts. Structure and Analysis, 1985, 2.‏

[32] Turkoglu, H.. Sustainable development and quality

[33] of urban life. Procedia-Social and Behavioral Sciences, 2015, 202: 10-14.

[34] Wright, I. C.. A review of research into engineering

[35] change management: implications for product design.

[36] Design Studies, 1997, 18(1): 33-42.

[37] Xu, L. D., Xu, E. L., & Li, L.. Industry 4.0: state of

[38] the art and future trends. International Journal of Production Research, 2018, 56(8): 2941-2962.‏



  • There are currently no refbacks.
Copyright © 2020 Anoushe Arab

Creative Commons License
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.